Ask the B&B: Do Bad Panel Gaps Mean Poor Vehicle Quality?

Mark Stevenson
by Mark Stevenson

These photos are of a vehicle that recently visited my driveway for a week. I’m not going to tell you what that vehicle is — yet — but it does raise a very interesting question.

Are bad panel gaps an indicator of a poor quality product? And what “quality” are we talking about anyway?

I ask this question genuinely because there are all kinds of reasons why panels wouldn’t line up quite like they should.

Gaps could still be within tolerance

While a panel gap may look visually unappealing, the measurements themselves could still be within tolerances specified by the automaker. If so, the people on the assembly line are simply doing their job to spec. However, it could also mean those tolerances account for far too wide of a variance.

It could be a one-off issue

The panels on one particular vehicle may be poorly matched, but one vehicle does not a trend make.

Panels aren’t mechanical systems

Exterior panels are not subject to the same tolerances as mechanical parts because they don’t need to be. Outside of vast misalignments of panels that may make a door pinch a front quarter panel when opened, a large or awkward gap between misaligned panels is going to have very little effect on the performance of your vehicle.

However, this is me playing devil’s advocate. All of these reasons seem fairly ludicrous in today’s high-tech world of manufacturing. We have lasers — freakin’ lasers! — in factories now. And robots. And robots with lasers for eyes.

But, are these gaps indicative of other problems? If an automaker doesn’t care to button up visual issues on vehicles rolling off the factory line — even after what we can presume are quality checks at the end for such issues — are those same people overlooking other issues as well?

Lexus is notoriously known for minding the gap. Lesser-known gapminder Hyundai inspired General Motors to do a better job of fitting panels.

However, it seems the automaker that buttoned together the vehicle pictured didn’t learn the same lesson.

What do you think, B&B?

Mark Stevenson
Mark Stevenson

More by Mark Stevenson

Comments
Join the conversation
2 of 141 comments
  • 66 West 66 West on Nov 27, 2015

    How long do we have to wait to find out what car it is? :)

  • Zoomzoomfan Zoomzoomfan on Dec 22, 2015

    I'm not sure if the panel gaps reflect poor overall quality, but that's certainly what it'd lead me to believe. How can the mechanical bits be trustworthy (or even the electrical) if they can't get the doors to fit together well? The issue is, however, most Americans would NEVER notice that nor would they particularly care if they did.

  • Lou_BC "That’s expensive for a midsize pickup" All of the "offroad" midsize trucks fall in that 65k USD range. The ZR2 is probably the cheapest ( without Bison option).
  • Lou_BC There are a few in my town. They come out on sunny days. I'd rather spend $29k on a square body Chevy
  • Lou_BC I had a 2010 Ford F150 and 2010 Toyota Sienna. The F150 went through 3 sets of brakes and Sienna 2 sets. Similar mileage and 10 year span.4 sets tires on F150. Truck needed a set of rear shocks and front axle seals. The solenoid in the T-case was replaced under warranty. I replaced a "blend door motor" on heater. Sienna needed a water pump and heater blower both on warranty. One TSB then recall on spare tire cable. Has a limp mode due to an engine sensor failure. At 11 years old I had to replace clutch pack in rear diff F150. My ZR2 diesel at 55,000 km. Needs new tires. Duratrac's worn and chewed up. Needed front end alignment (1st time ever on any truck I've owned).Rear brakes worn out. Left pads were to metal. Chevy rear brakes don't like offroad. Weird "inside out" dents in a few spots rear fenders. Typically GM can't really build an offroad truck issue. They won't warranty. Has fender-well liners. Tore off one rear shock protector. Was cheaper to order from GM warehouse through parts supplier than through Chevy dealer. Lots of squeaks and rattles. Infotainment has crashed a few times. Seat heater modual was on recall. One of those post sale retrofit.Local dealer is horrific. If my son can't service or repair it, I'll drive 120 km to the next town. 1st and last Chevy. Love the drivetrain and suspension. Fit and finish mediocre. Dealer sucks.
  • MaintenanceCosts You expect everything on Amazon and eBay to be fake, but it's a shame to see fake stuff on Summit Racing. Glad they pulled it.
  • SCE to AUX 08 Rabbit (college car, 128k miles): Everything is expensive and difficult to repair. Bought it several years ago as a favor to a friend leaving the country. I outsourced the clutch ($1200), but I did all other work. Ignition switch, all calipers, pads, rotors, A/C compressor, blower fan, cooling fan, plugs and coils, belts and tensioners, 3 flat tires (nails), and on and on.19 Ioniq EV (66k miles): 12V battery, wipers, 1 set of tires, cabin air filter, new pads and rotors at 15k miles since the factory ones wore funny, 1 qt of reduction gear oil. Insurance is cheap. It costs me nearly nothing to drive it.22 Santa Fe (22k miles): Nothing yet, except oil changes. I dread having to buy tires.
Next